CCNP MAY ENGLISH Need User and Pass to ENV-Lite VM Workstation

Good day, This is regarding the May classes for CCNP.
I worked to login into the EVE client on vm with the usename and pass as described for the download and also a few others and have been met with username and pass incorrect. Does anyone know the user and pass to login to the EVE-ng client?

1 Like

user root pass eve for CLI
user admin pass eve for GUI Web

Good day, thank you for your response. It appears the CLI uses root and eve for pass I am unfamiliar with the ip to get onto the web if you could assist with that I would appreciate it. Thank you

The other questions I have is now do I get to the area on the web to perform the recreation of the class room networks for lab work?

login to cli
ifconfig | grep 192

will give u ip add of eve-ng

I Have a question on the 1006 internal vlan. If these are cisco switches and vtp is running the 1006 will populate to the other swtich so we will know it already exists, however, if I am hearing this correctly these vlans are not shared between switches. Therefore, the due diligence of research to determine which vlans were on the up stream switch before you assign to the downstream would be the best practice. Correct?

Semir,
Hi, I need the link to you google drive for the lab my browser closed before I could book mark it. Thank you
Debra

Hi Samir,

i am getting below errors when configuring port channel …please suggest …

*Jun 15 17:06:23.815: %EC-5-L3DONTBNDL2: Et0/1 suspended: LACP currently not enabled on the remote port.
*Jun 15 17:06:23.974: %SYS-5-CONFIG_I: Configured from console by console
*Jun 15 17:06:24.193: %EC-5-L3DONTBNDL2: Et0/0 suspended: LACP currently not enabled on the remote port.
SW2#sh

one side port channel is coming up but other side is it not routed , is in down status

use cisco viosl2 image instead of cisco iol image

Simar, Thank you very much I appreciate it.

thanks Samir ! i used Violsl2 image however same errors getting …exploring more to troubleshoot …same response on switch port not lacp error is same … switch 2 config logs below

Switch#
*Jun 17 17:21:58.267: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
*Jun 17 17:21:58.514: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
*Jun 17 17:21:59.267: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
*Jun 17 17:21:59.514: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
*Jun 17 17:21:59.635: %SYS-5-CONFIG_I: Configured from console by console
*Jun 17 17:22:05.293: %EC-5-L3DONTBNDL2: Gi0/1 suspended: LACP currently not enabled on the remote port.
*Jun 17 17:22:05.356: %EC-5-L3DONTBNDL2: Gi0/0 suspended: LACP currently not enabled on the remote port.
Switch#sh ip int br
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/2 unassigned YES unset up up
GigabitEthernet0/3 unassigned YES unset up up
GigabitEthernet0/0 unassigned YES manual up up
GigabitEthernet0/1 unassigned YES manual up up
GigabitEthernet1/0 unassigned YES unset up up
GigabitEthernet1/1 unassigned YES unset up up
GigabitEthernet1/2 unassigned YES unset up up
GigabitEthernet1/3 unassigned YES unset up up
GigabitEthernet2/0 unassigned YES unset up up
GigabitEthernet2/1 unassigned YES unset up up
GigabitEthernet2/2 unassigned YES unset up up
GigabitEthernet2/3 unassigned YES unset up up
GigabitEthernet3/0 unassigned YES unset up up
GigabitEthernet3/1 unassigned YES unset up up
GigabitEthernet3/2 unassigned YES unset up up
GigabitEthernet3/3 unassigned YES unset up up
Port-channel1 192.168.112.2 YES manual up up
Switch# sh int stst
Switch# sh int status

Port Name Status Vlan Duplex Speed Type
Gi0/2 connected 1 auto auto unknown
Gi0/3 connected 1 auto auto unknown
Gi0/0 connected routed auto auto unknown
Gi0/1 connected routed auto auto unknown
Gi1/0 connected 1 auto auto unknown
Gi1/1 connected 1 auto auto unknown
Gi1/2 connected 1 auto auto unknown
Gi1/3 connected 1 auto auto unknown
Gi2/0 connected 1 auto auto unknown
Gi2/1 connected 1 auto auto unknown
Gi2/2 connected 1 auto auto unknown
Gi2/3 connected 1 auto auto unknown
Gi3/0 connected 1 auto auto unknown
Gi3/1 connected 1 auto auto unknown
Gi3/2 connected 1 auto auto unknown
Gi3/3 connected 1 auto auto unknown
Po1 connected routed auto auto
Switch# wr me
Switch# wr memory
Building configuration…
Compressed configuration from 3673 bytes to 1674 bytes[OK]
Switch#
*Jun 17 17:24:15.588: %GRUB-5-CONFIG_WRITING: GRUB configuration is being updated on disk. Please wait…
*Jun 17 17:24:16.558: %GRUB-5-CONFIG_WRITTEN: GRUB configuration was written to disk successfully.
Switch#ping 192.168.112.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.112.2, timeout is 2 seconds:
!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 3/5/14 ms
Switch#ping 192.168.112.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.112.1, timeout is 2 seconds:
…
Success rate is 0 percent (0/5)
Switch#

Switch 1 logs …

Switch(config-if-range)#no shutdown
Switch(config-if-range)#
*Jun 17 17:21:56.594: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
*Jun 17 17:21:56.842: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
*Jun 17 17:21:57.594: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
*Jun 17 17:21:57.843: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
*Jun 17 17:22:03.301: %EC-5-L3DONTBNDL2: Gi0/1 suspended: LACP currently not enabled on the remote port.
*Jun 17 17:22:03.410: %EC-5-L3DONTBNDL2: Gi0/0 suspended: LACP currently not enabled on the remote port.
Switch(config-if-range)#
Switch(config-if-range)#
Switch(config-if-range)#
Switch(config-if-range)#^Z
Switch#sh ip

Hi, Am Ithe only one that does not see Sundays doc in the Samir google share drive ? The last one I see is VTP

My browser was not updating or showing the full drive. I see all the docs within your folder it must be a laptop memory and browser issue. Sorry

Hi, Wireshark does not want to run on my labs does anyone else have that issue?

I installed a new version and my Wirehark is working now

Hi, I failed to ask since Saturday is a Holiday the 4th of July are we still having class?

Home Official Website Video Portal